How to Convert Cubic Yards to Tons of Rip Rap ... If the riprap consists of crushed stone, its density is 2,500 pounds per cubic yard. If it contains mostly gravel, its density is 2,700 pounds per cubic yard. If the riprap contains concrete or limestone rubble, it has a density of 4,050 or 4,600 pounds per cubic yard, respectively. ...
Re: Cubic Meters to Metric Ton Using Gravel I found the following density data for gravel. Gravel, loose, dry - 1.52 tonne/cubic meter Gravel, w/sand, natural - 1.92 tonne/cubic meter
Type in inches and feet of your project and calculate the estimated amount of Sand / Screenings in cubic yards, cubic feet and Tons, that your need for your project. The Density of Crusher Run: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t
Most of Harmony Sand & Gravel's products will weight approximately 2,840 pounds per cubic yard or about 1.42 tons per cubic yard. For estimating purposes, most Contractor's consider the yield to be 3,000 pounds per cubic yard or 1.5 tons per cubic yard.
Sometimes crushed stone is sold by the ton. To figure out the how many tons you will need is not hard to do. You will have to know that the standard weight contractors use for crushed stone is 2700 pounds per cubic yard. Multiply the number of cubic yards by 2700 and divide by 2000. This value is the number of tons that you will need.
The weight of gravel per cubic yard is approximately 2,970 pounds, or 1.48 tons, if the gravel is dry. If the gravel is out of water, the weight per cubic yard is approximately 1,620 pounds or .81 tons. Comparatively, other building materials are much heavier or much lighter.
Project and Material Resources. At Braen Stone we strive to make your experience as smooth as possible. As one of the largest suppliers of construction materials in NJ, NY, PA & CT we wanted to share some of the resources that our team finds most helpful.
Jun 09, 2005· This table has in-truck and placed densities. SO a crushed gravel is about 1.43 T/cy in the truck and 1.85 T/cy placed, typ. They note that placed density varies from 1.7 to 1.9 T/cy, with the lower end of the range for materials with say 40% sand and the upper end for more open-graded ballast.
Material Coverage & Conversion Chart All rock products, rip rap, boulders and soils are sold by the ton. All mulches and plant mixes are sold by cubic yard. 1 Ton/Cy of the material listed below at a 3" depth will cover square feet Concrete Sand 86 Sq. Ft. Squeege 83 Sq. Ft. Pea Gravel 83 Sq. Ft. 314" Rock 77 Sq. Ft. 1 112" Rock 77 Sq. Ft.
Gabion Stone ( 150-250mm) 1.2 per cubic meter. Lias 2.48 tonnes per cubic metre Granite 2.72 tonnes per cubic metre Slate 2.8 tonnes per cubic metre flint 2.3 tonnes per cubic metre Yorkstone 2.5 tonnes per cubic metre Brick rubble 1.8 - 2.2 tonnes per cubic metre . 1 yard of soil = 1.45 tons of soil, please don`t ask how i worked it out
Calculator. Cubic Yards for a ... -1 cubic yard = 1 ton Unscreened topsoil 1:1.3 -1 cubic yard = 1 1/3 tons Gravel Bank run gravel 1:2-2" Screened gravel 1:2 1" and 2" Gravel 1:2-1 cubic yard = 2 tons 3"-6" oversized rock 1:1.5 8"-18" oversized rock 1:1.5-1 cubic yard = 1 1/2 tons Crushed Aggregates #1 Crushed limestone 1:1.5
This construction conversion tool has been designed to help you convert between different units of weight and volume. Please note that if you are converting between units of volume and weight, you should consider reading how to convert from volume to weight beforehand. This type of conversion requires a substance density figure.A list of some common construction density approximations is ...
Crushed stone is produced by passing stones through a crushing machine at a quarry. Various types of stone are used in this operation, such as granite and limestone. At the bottom of the crushing machine lies a screen that traps the the crushed stone product (the finer material that passes through the screen is also kept and sold -- as stone dust).
Stone, crushed weighs 1.602 gram per cubic centimeter or 1 602 kilogram per cubic meter, i.e. density of stone, crushed is equal to 1 602 kg/m³. In Imperial or US customary measurement system, the density is equal to 100 pound per cubic foot [lb/ft³], or 0.926 ounce per cubic inch [oz/inch³] .
Typical gravel density (dry) is between 1520 and 1680 kg/m3 (95 to 105 lbs/ft3). If it is mixed with sand the density is around 1920 kg/m3 or 120 lbs/ft3 . Common gravel and crushed stone sizes. Contrary to what you may think, there is more than one type of gravel, both by composition and size of the stones.
Pennsy Supply is the largest producer of aggregate in central Pennsylvania, producing more than nine million tons every year consisting of primarily crushed stone, sand and gravel. Quality construction materials are at the core of Pennsy Supply!
Crushed stone density is variable ranging from 2.4 - 2.7 Metric Tons per cubic Meter depending on the type of stone, the stone crushing machinery, and how the crushed stone is sorted after crushing.
The products shown below are available at The Stone Store, a division on Aggtrans, in Hanover, Maryland. Products are available in bulk and bagged in three sizes; 2000#, 250#, 50#. If you require larger quantities, such as: full truck loads (22 Tons) or more, products will be direct shipped.
This calculator will estimate how much stone and/or sand (in tons) that are required for your job based on your material type and measurements. Please be advised that the total calculated tons may differ from your actual requirement due to variances in sub-grade depth, compaction, material density…
Step 2: Enter the length, width and depth of area to fill (NOTE: depth is in inches, not feet): Step 3: Click Calculate to get amount needed
#53 Driveway Stone - Crushed Limestone Home > Shop > Shop Rock and Stone > Shop Driveway Stone > #53 Driveway Stone – Crushed Limestone. Prev / Next #53 Driveway Stone – Crushed Limestone $ 39.50. Per Cubic Yard #53 same as #4 but with limestone dust for easy packing 1″-2″ in size with half lime dust.
The densities (pounds per square foot, or tons per cubic yard, sometimes called "pounds per foot" or "tons per cube") will also vary according to the season, the saturation levels (dampness) of the piles of medium when you purchase the mediums, the quality of the sieves used to sort the crusher …
These values for density of some common building materials were collected from sites across the Internet and are generally in agreement with multiple sites. Most are from BOCA or ASAE tables. However, if you have values that you believe are more accurate, use them for your calculations, and please send me an e-mail to let me know what your ...
Crushed aggregate, one-inch crushed concrete, recycled asphalt, 3/8-inch pea gravel, 2-inch sewer filter rock, and concrete and asphalt aggregate blends all weigh in at 1.07 tons. Pit run gravel follows at 1.25 tons per cubic meter, regardless of whether it is 2-inch or 4-inch.
Crushed stone and/or sand and gravel products suitable for every type and size of construction project are available at 15 Tilcon locations throughout Connecticut. If you need assistance estimating the stone requirements for your project or require further information, please call Tilcon Crushed Stone sales at 860-224-6010, or fax us at 860-225 ...
Minimum Cost: $27.50 per ton of basic landscaping crushed stone when 23 or more tons are purchased at one time. Costs increase per ton when fewer tons are ordered. Maximum Cost: $64.20 per ton of white marble crushed stone, not including delivery. Crushed Stone Cost Factors. As you saw above, there is quite a range for crushed stone prices.
The Tonnage Calculator helps you to estimate the amount of aggregate required for your job. Please note that densities will vary somewhat between different loads, but the default values assigned for the various aggregates are good standard "rules of thumb" for estimating.
Granite (all) = 1.325 tons (2650 lbs.) per cubic yard; Marble (all) = 1.35 tons (2700 lbs.) per cubic yard; Cubic Footage Per Ton Of Building Stone & Flagstone. 15 cubic feet per ton* or 133 lbs. per cubic foot* *Note: The true cubic footage weights are 145-160 pounds per cubic foot, for solid unbroken stone, or about 13 cubic feet per ton on ...
An estimated density factor should then appear in the above density field. Geology: Traprock Limestone Granite Sand & Gravel Sandstone Other Product: Screenings Crushed Stone Base / Crusher Run Coarse Aggregates Sand Riprap Other
Crushed Stone 2,700 lb. Plywood Sheets 800 lb. Earth (loose) 2,050 lb. Roofing Debris 450 lb. to 750 lb. Earth (packed) 2,565 lb. Sand (dry) 2,750 lb.